Saving Energy in the GFRP Pultrusion Process
DOI:
https://doi.org/10.6000/1929-5995.2013.02.02.7Keywords:
Pultrusion process, Die heating system, Heaters position configuration, Energy performance, Numerical analysisAbstract
This study addresses to the optimization of pultrusion manufacturing process from the energy-consumption point of view. The die heating system of external platen heaters commonly used in the pultrusion machines is one of the components that contribute the most to the high consumption of energy of pultrusion process. Hence, instead of the conventional multi-planar heaters, a new internal die heating system that leads to minor heat losses is proposed. The effect of the number and relative position of the embedded heaters along the die is also analysed towards the setting up of the optimum arrangement that minimizes both the energy rate and consumption. Simulation and optimization processes were greatly supported by Finite Element Analysis (FEA) and calibrated with basis on the temperature profile computed through thermography imaging techniques.
The main outputs of this study allow to conclude that the use of embedded cylindrical resistances instead of external planar heaters leads to drastic reductions of both the power consumption and the warm-up periods of the die heating system. For the analysed die tool and process, savings on energy consumption up to 60% and warm-up period stages less than an half hour were attained with the new internal heating system. The improvements achieved allow reducing the power requirements on pultrusion process, and thus minimize industrial costs and contribute to a more sustainable pultrusion manufacturing industry.
References
Hollaway LC. A review of the present and future utilisation of FRP composites in the civil infrastructure with reference to their important in-service properties. Constr Build Mater 2010; 24: 2419-45. http://dx.doi.org/10.1016/j.conbuildmat.2010.04.062 DOI: https://doi.org/10.1016/j.conbuildmat.2010.04.062
Correia JPRR, Branco FAB, Gonilha JMCA, Ferreira D, Reis L. 2011a. GFRP sandwich panels for civil engineering structural applications. In: Proceedings of the ACE-X2011 - 5th. International Conference on Advanced Computational Engineering and Experimenting; 2011: Jul 3-6 July; Vilamoura, Portugal.
Ribeiro MCS, Ferreira AJM, Marques AT. Analysis and experiments on GFRP-Polymer Concrete Hybrid Beams. J Polym Eng 2003; 23: 337-51. http://dx.doi.org/10.1515/POLYENG.2003.23.5.337 DOI: https://doi.org/10.1515/POLYENG.2003.23.5.337
Ferreira AJM, Ribeiro MCS, Marques AT. Analysis of hybrid beams of polymer concrete and composite materials. Int J Mech Mater Design 2004; 1: 143-55. http://dx.doi.org/10.1007/s10999-004-1493-0 DOI: https://doi.org/10.1007/s10999-004-1493-0
Shaw-Stewart D, Sumerak JE. The pultrusion process. In: Starr TF, editor. Pultrusion for Engineers. 1st ed. Abington Cambridge: Woodhead Publishing Ltd. 2000; pp. 19-65. DOI: https://doi.org/10.1533/9781855738881.19
Joshi SC, Lam YC, Zaw K. Optimization for quality thermosetting composites pultrudate through die heater layout and power control. In: Proceedings of 16th International Conference on composite Materials 2007: Jul 8-13; Kyoto, Japan.
Moschiar SM, Reboredo MM, Vazquez A. Pultrusion Processing. In: Cheremisinoff NP, editor. Advanced Polymer
Processing Operations. New Jersey: Noyes Publications 1998; pp. 126-56. http://dx.doi.org/10.1016/B978-081551426-8.50009-X DOI: https://doi.org/10.1016/B978-081551426-8.50009-X
Suratno BR, Ye L, Mai YW. Simulation of temperature and curing profiles in pultruded composite rods. Compos Sci Technol 1998; 58: 191-7. http://dx.doi.org/10.1016/S0266-3538(97)00132-2 DOI: https://doi.org/10.1016/S0266-3538(97)00132-2
Valliappan M, Roux JA, Vaughan JG, Arafat ES. Die and post-die temperature and cure in graphite/epoxy composites. Compos Part B-Eng 1996; 27B: 1-9. http://dx.doi.org/10.1016/1359-8368(95)00001-1 DOI: https://doi.org/10.1016/1359-8368(95)00001-1
Gorthala R, Roux JA, Vaughan JG. Resin flow, cure and heat transfer analysis for pultrusion process. J Compos Mater 1994; 28: 486-506. DOI: https://doi.org/10.1177/002199839402800601
Sarrionandia M, Mondragón I. Heat transfer for pultrusion of a modified acrylic/glass reinforced composite. Polym Composite 2002; 23: 21-7. http://dx.doi.org/10.1002/pc.10408 DOI: https://doi.org/10.1002/pc.10408
Safonov AA, Suvorova YV. Optimization of the pultrusion process for a rod with a large diameter. J Mach Manuf Reliab 2009; 38: 572-8. http://dx.doi.org/10.3103/S1052618809060090 DOI: https://doi.org/10.3103/S1052618809060090
Liu XL, Hillier W. Heat transfer and cure analysis for the pultrusion of a fiberglass-vinyl ester I beam. Compos Struct 1999; 47: 581-8. http://dx.doi.org/10.1016/S0263-8223(00)00029-5 DOI: https://doi.org/10.1016/S0263-8223(00)00029-5
Liu XL, Crouch IG, Lam YC. Simulation of heat transfer and cure in pultrusion with a general-purpose finite element package. Compos Sci Technol 2000; 60: 857-64. http://dx.doi.org/10.1016/S0266-3538(99)00189-X DOI: https://doi.org/10.1016/S0266-3538(99)00189-X
Joshi SC, Lam YC. Three-dimensional finite-element/nodal-control-volume simulation of the pultrusion process with temperature-dependent material properties including resin shrinkage. Compos Sci Technol 2001; 61: 1539-47. http://dx.doi.org/10.1016/S0266-3538(01)00056-2 DOI: https://doi.org/10.1016/S0266-3538(01)00056-2
Lam YC, Li J, Joshi SC. Simultaneous optimization of die-heating and pull-speed in pultrusion of thermoset composites. Polym Composite 2003; 24: 199-209. http://dx.doi.org/10.1002/pc.10020 DOI: https://doi.org/10.1002/pc.10020
Joshi SC, Lam YC, Tun UW. Improved cure optimization in pultrusion with pre-heating and die-cooler temperature. Compos Part A-Appl S 2003; 34: 1151-59. http://dx.doi.org/10.1016/j.compositesa.2003.08.003 DOI: https://doi.org/10.1016/j.compositesa.2003.08.003
Joshi SC, Lam YC. Integrated approach for modelling cure and crystallization kinetics of different polymers in 3D pultrusion simulation. J Mater Process Tech 2006; 174: 178-82. http://dx.doi.org/10.1016/j.jmatprotec.2006.01.003 DOI: https://doi.org/10.1016/j.jmatprotec.2006.01.003
Chen X, Xie H, Chen H, Zhang F. Optimization for CFRP pultrusion process based on genetic algotithm-neural network. Int J Mater Forum 2010; 3: S1391-9. DOI: https://doi.org/10.1007/s12289-010-0684-5
Khan WA, Methven J. Determination of Duty Cycle in Thermoset Pultrusion. In Proceedings of 17th International Conference on composite Materials 2009: Jul 27-31; Edinburgh, UK.
Sumerack JE. Experimental Measurements of Pultrusion Die/Heater Interface – Effects on Process Stability and Economics. In: Proceedings of COMPOSITES 2002 Convention and Trade Show 2002: Sep 25-27; Atlanta, USA.
Srinivasagupta D, Kardos JL. Ecologically and economically conscious design of the injected pultrusion process via multi-objective optimization. Model Simul Mater Sc 2004: 12: S205. http://dx.doi.org/10.1088/0965-0393/12/3/S10 DOI: https://doi.org/10.1088/0965-0393/12/3/S10
Santos LS, Pagano RL, Biscaia EC, Calado VMA. Optimum heating configuration of pultrusion process. Comput Aided Chem Eng 2009; 27: 705-10.
Santos LS, Calado VMA, Giovanelli L, Nóbrega M, Pagano R, Biscaia E. Application of a CFD-based tool to optimise an industrial pultrusion process. In: Proceedings of 2nd International Conference on Engineering Optimization 2010: Sep 6-9; Lisbon, Portugal. http://dx.doi.org/10.1016/S1570-7946(09)70338-4 DOI: https://doi.org/10.1016/S1570-7946(09)70338-4
Sumerak JE. Pultrusion die design optimization opportunities using thermal finite element analysis techniques. In: Proceedings of the 49th Annual RP/CI, SPI Conference 1994: Feb; Cincinnati, USA.
Downloads
Published
How to Cite
Issue
Section
License
Copyright (c) 2013 Journal of Research Updates in Polymer Science
This work is licensed under a Creative Commons Attribution-NonCommercial 4.0 International License.
Policy for Journals/Articles with Open Access
Authors who publish with this journal agree to the following terms:
- Authors retain copyright and grant the journal right of first publication with the work simultaneously licensed under a Creative Commons Attribution License that allows others to share the work with an acknowledgement of the work's authorship and initial publication in this journal.
- Authors are permitted and encouraged to post links to their work online (e.g., in institutional repositories or on their website) prior to and during the submission process, as it can lead to productive exchanges, as well as earlier and greater citation of published work
Policy for Journals / Manuscript with Paid Access
Authors who publish with this journal agree to the following terms:
- Publisher retain copyright .
- Authors are permitted and encouraged to post links to their work online (e.g., in institutional repositories or on their website) prior to and during the submission process, as it can lead to productive exchanges, as well as earlier and greater citation of published work .
